User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Honeywell 1883A-MPD:Plug-In
DATE:                  09-Aug-97
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       23
NUMBER OF LINES:       175
CONFIGURATION:         Fluke 5700A
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-   R     N              P   S         M              F        W
  1.002  ASK+                                          X
  1.003  HEAD         INITIAL CONDITIONS
  1.004  DISP         With the exception of the module to be tested, make sure
  1.004  DISP         all other modules in the mainframe are OFF.
  1.005  DISP         Set all the VAR controls full CW.
  1.006  HEAD         {* Range Tests *}
  1.007  JMP          2.001
  1.008  EVAL
  2.001  DISP         Set the UUT as follows:
  2.001  DISP         SENS ............................... .5 V/DIV
  2.001  DISP         TIMELINE ........................... OFF
  2.001  DISP         GRIDLINE ........................... CONT
  2.001  DISP         RECORD SPEED ....................... 1 in/sec
  2.001  DISP         MULTIPLIER ......................... 0.1
  2.002  DISP         Connect the 5700 V/ê/A output to the UUT BNC input.
  2.003  DISP         Open the paper housing to expose the CRT.
  2.004  5700         0V                                                S  2W
  2.005  DISP         Adjust the POS control on the UUT to line up the
  2.005  DISP         cursor with the left most grid marker.
  2.006  5700         3.5V                                              S  2W
  2.007  DISP         Adjust the TRIM control to position the UUT cursor
  2.007  DISP         on the 35th (from left) grid marker.
  2.007  DISP
  2.007  DISP         It may be necessary to get a printout to make this
  2.007  DISP         adjustment.
  2.008  HEAD         { .2V/DIV }
  2.009  JMP          3.001
  2.010  EVAL
  3.001  5700         0V                                                S  2W
  3.002  DISP         Set the UUT as follows:
  3.002  DISP         SENS ............................... .2 V/DIV
  3.003  DISP         Adjust the POS control if necessary.
  3.004  MESS         Adjust the 5700 output so the UUT cursor is
  3.004  MESS         on the 35th grid marker.
  3.005  5700         1.400V         1.000%                                2W
#!          Test Tol 0.014, Sys Tol 9.6e-006, TUR 1458.333 (>= 4.00).
  4.001  HEAD         { .1V/DIV }
  4.002  JMP          5.001
  4.003  EVAL
  5.001  5700         0V                                                S  2W
  5.002  DISP         Set the UUT as follows:
  5.002  DISP         SENS ............................... .1 V/DIV
  5.003  DISP         Adjust the POS control if necessary.
  5.004  MESS         Adjust the 5700 output so the UUT cursor is
  5.004  MESS         on the 35th grid marker.
  5.005  5700         0.7000V        1.000%                                2W
#!          Test Tol 0.007, Sys Tol 5.4e-006, TUR 1296.296 (>= 4.00).
  6.001  HEAD         { .05V/DIV }
  6.002  JMP          7.001
  6.003  EVAL
  7.001  5700         0V                                                S  2W
  7.002  DISP         Set the UUT as follows:
  7.002  DISP         SENS ............................... .05 V/DIV
  7.003  DISP         Adjust the POS control if necessary.
  7.004  MESS         Adjust the 5700 output so the UUT cursor is
  7.004  MESS         on the 35th grid marker.
  7.005  5700         0.3500V        1.000%                                2W
#!          Test Tol 0.0035, Sys Tol 3.3e-006, TUR 1060.606 (>= 4.00).
  8.001  HEAD         {}
  8.002  HEAD         {* Linearity Test *}
  8.003  HEAD         Linearity Test
  8.004  JMP          9.001
  8.005  EVAL
  9.001  5700         0V                                                S  2W
  9.002  DISP         Set the UUT as follows:
  9.002  DISP         SENS ............................... .5 V/DIV
  9.003  DISP         Adjust the POS control if necessary.
  9.004  MESS         Adjust the 5700 output so the UUT cursor is
  9.004  MESS         on the 30th grid marker.
  9.005  5700         3.000V         0.0140U                               2W
#!          Test Tol 0.014, Sys Tol 1.9e-005, TUR 736.842 (>= 4.00).
 10.001  MESS         Adjust the 5700 output so the UUT cursor is
 10.001  MESS         on the 25th grid marker.
 10.002  5700         2.500V         0.0140U                               2W
#!          Test Tol 0.014, Sys Tol 1.65e-005, TUR 848.485 (>= 4.00).
 11.001  MESS         Adjust the 5700 output so the UUT cursor is
 11.001  MESS         on the 20th grid marker.
 11.002  5700         2.000V         0.0140U                               2W
#!          Test Tol 0.014, Sys Tol 1.32e-005, TUR 1060.606 (>= 4.00).
 12.001  MESS         Adjust the 5700 output so the UUT cursor is
 12.001  MESS         on the 15th grid marker.
 12.002  5700         1.500V         0.0140U                               2W
#!          Test Tol 0.014, Sys Tol 1.02e-005, TUR 1372.549 (>= 4.00).
 13.001  MESS         Adjust the 5700 output so the UUT cursor is
 13.001  MESS         on the 10th grid marker.
 13.002  5700         1.000V         0.0140U                               2W
#!          Test Tol 0.014, Sys Tol 7.2e-006, TUR 1944.444 (>= 4.00).
 14.001  MESS         Adjust the 5700 output so the UUT cursor is
 14.001  MESS         on the 5th grid marker.
 14.002  5700         0.500V         0.0140U                               2W
#!          Test Tol 0.014, Sys Tol 4.2e-006, TUR 3333.333 (>= 4.00).
 15.001  MESS
 15.002  HEAD         {}
 15.003  HEAD         {* Frequency Response *}
 15.004  HEAD         { Referenced to 400Hz }
 15.005  HEAD         Frequency Response
 15.006  JMP          16.001
 15.007  EVAL
 16.001  DISP         Adjust the UUT cursor to the middle grid marker.
 16.002  MATH         mem = 1.25
 16.003  MESS         Using the UUT POS and the 5700A AMPTD MODIFY
 16.003  MESS         controls, adjust the display for a deflection of
 16.003  MESS         35 gridlines.
 16.004  5700         V                            400H                 N  2W
 16.005  MEME                                                     >1
 16.006  JMP          17.001
 16.007  EVAL
 17.001  MESS         Adjust the 5700A amplitude output for a deflection of
 17.001  MESS         35 gridlines.
 17.002  MEME                                                     <1
 17.003  5700         V                            10H                  N  2W
 17.004  MEME
 17.005  MEME                                                     <1
 17.006  MEMC         V              0.500%        10H
#!          Test Tol 0.00625, Sys Tol 0.0007875, TUR 7.937 (>= 4.00).
 18.001  MEME                                                     <1
 18.002  MESS         Adjust the 5700A amplitude output for a deflection of
 18.002  MESS         35 gridlines.
 18.003  5700         V                            100H                 N  2W
 18.004  MEME
 18.005  MEME                                                     <1
 18.006  MEMC         V              0.500%        100H
#!          Test Tol 0.00625, Sys Tol 0.00010075, TUR 62.035 (>= 4.00).
 19.001  MEME                                                     <1
 19.002  MESS         Adjust the 5700A amplitude output for a deflection of
 19.002  MESS         35 gridlines.
 19.003  5700         V                            1kH                  N  2W
 19.004  MEME
 19.005  MEME                                                     <1
 19.006  MEMC         V              0.500%        1kH
#!          Test Tol 0.00625, Sys Tol 0.00010075, TUR 62.035 (>= 4.00).
 20.001  MEME                                                     <1
 20.002  MESS         Adjust the 5700A amplitude output for a deflection of
 20.002  MESS         35 gridlines.
 20.003  5700         V                            2kH                  N  2W
 20.004  MEME
 20.005  MEME                                                     <1
 20.006  MEMC         V              1.300%        2kH
#!          Test Tol 0.01625, Sys Tol 0.00010075, TUR 161.290 (>= 4.00).
 21.001  MEME                                                     <1
 21.002  MESS         Adjust the 5700A amplitude output for a deflection of
 21.002  MESS         35 gridlines.
 21.003  5700         V                            3kH                  N  2W
 21.004  MEME
 21.005  MEME                                                     <1
 21.006  MEMC         V              3.000%        3kH
#!          Test Tol 0.0375, Sys Tol 0.00010075, TUR 372.208 (>= 4.00).
 22.001  MEME                                                     <1
 22.002  MESS         Adjust the 5700A amplitude output for a deflection of
 22.002  MESS         35 gridlines.
 22.003  5700         V                            5.01kH               N  2W
 22.004  MEME
 22.005  MEME                                                     <1
 22.006  MEMC         V              8.000%        5.01kH
#!          Test Tol 0.1, Sys Tol 0.00010075, TUR 992.556 (>= 4.00).
 23.001  HEAD         {}
 23.002  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.